<p>
<b><font face="Arial" size="2">USES:</font></b></p>
<p>
Deep cleaning of outdoor condenser coils to restore efficiency and increase performance of the system.</p>
<p>
<b><font face="Arial" size="2">DILUTION RATIOS:</font></b></p>
<p style="text-align: justify;">
Because RXSOL-41-8672-025 is highly concentrated, it must be diluted prior to use. Dilution also improves penetration into the coil and increases product performance. Actual dilution ratios will vary according to the application. The following is intended as a general<br />
guideline:</p>
<ul>
<li>
Up to 8-10 parts water to 1 part  RXSOL-41-8672-025 coil cleaner  for light cleaning and brightening, when expanding foam is not required.</li>
<li>
3-5 parts water to 1 part RXSOL-41-8672-025 coil cleaner on difficult cleaning tasks.</li>
<li>
1-2 parts water to 1 part RXSOL-41-8672-025 coil cleaner  for use as a high foaming,aluminum finned, air cooled condenser coil cleaner.Use the minimum concentration required to accomplish your task.</li>
</ul>
<p style="text-align: justify;">
Note: Do not use RXSOL-41-8672-025 coil cleaner at concentrations greater than 1:1 (less than 1 part water to 1 part RXSOL-41-8672-025 coil cleaner. Rinse the treated surfaces as well as the surrounding area thoroughly after use.</p>
<p>
<b><font face="Arial" size="2">APPLICATION METHODS:</font></b></p>
<p>
Low pressure, acid resistant tank sprayers are recommended.<br />
Regardless of application method, avoid inhalation of mist or contact of liquid or mist with skin.</p>
<p>
<b><font face="Arial" size="2">SUGGESTED INSTRUCTIONS FOR USE:</font></b></p>
<ul>
<li>
<font face="Arial" size="2"> When handling RXSOL-41-8672-025 coil cleaner or any other strong chemical, be sure to wear chemical impervious</font><font face="Arial" size="2">gloves,apron and splash goggles.</font><br />
 </li>
<li>
<font face="Arial" size="2">Determine required dilution ratio for the specific application. It is recommended to start with a dilution ratio of 10:1 and increase concentration until the desired results are achieved.</font><br />
 </li>
<li>
<font face="Arial" size="2">As with mixing all acids, place the desired amount of water into the tank and then add </font>RXSOL-41-8672-025 coil cleaner<br />
 </li>
<li>
<font face="Arial" size="2"> Turn off fans and allow hot coils to cool before applying.</font><br />
 </li>
<li>
<font face="Arial" size="2">Using plain water, wet both the condenser coil as well as the area surrounding the equipment. Wetting the coil with water aids in product penetration and performance.</font><br />
 </li>
<li>
<font face="Arial" size="2">Apply the properly diluted product to the coil surface. Whenever possible, apply solution from the outlet side of the coil. Allow product to remain on surface, normally 5-10 minutes. Do not allow product to dry on the coil. Note: In extreme cases, application may have to be repeated to achieve</font><font size="2"><font face="Arial"> </font></font>desired results.</li>
<li>
<font face="Arial" size="2">If foaming does not occur, check for extreme grease buildup which will slow cleaning process. Foaming may not occur if coil is coated or painted.</font><br />
 </li>
<li>
<font face="Arial" size="2">  Rinse coils, tools and surrounding area thoroughly after completing the coil cleaning process</font></li>
</ul>