HOLD BRIGHT
Part No. RXSOL-10-1027-025
Removes Salt rust protective Degreasing Compound
Salt Remover, Flash Rust Preventer, and Degreaser
Key Technical Details
| Part number | RXSOL-10-1027-025 |
|---|---|
| Generic name | Removes Salt rust protective Degreasing Compound |
| Standard packing | 25.00 |
| Available pack sizes | 25 Kgs Drum pack Removes Salt rust protective Degreasing Compound Feel free to ask for 5, 10, 20, 30, 60 Kg packing. We are keeping ready stock at Mumbai, Kandla, Chennai, Vizag, Kolkata, Fujairah, Dubai. |
Typical Use Case of HOLD BRIGHT is a water additive that prevents flash rusting of wet abrasive-and water-blasted iron and steel surfaces and of dry-blasted surfaces in a pressurised wash down. It effectively removes all salts, including chlorides, sulphates, phosphates, nitrates, etc. and other contaminants, including oil, grease, and blast residues.
- As a passivation rinse in steel processing
- For pipes, tanks, tools, flanges, and auto parts
- In metalworking shops, shipyards, and fabrication plants
- Temporary protection before painting or powder coating
Uses
Note: Water that contains a high concentration of salts, carbonates and/or bicarbonates (i.e. "hard water"), or other contaminants may interfere with the performance of HOLD BRIGHT. Industrial or plant water is often a problem, so should be avoided. In a few areas, even potable ("drinking") water may also be a problem. In most cases "bad" water can be corrected easily and inexpensively. Hard water may also be a problem for some equipment. Consult the manufacturer. In most localities, water treatment on site is accessible and inexpensive. If you are not obtaining the results you expect, it is possible that you have a water problem. Call our technical service staff if you have any concerns or questions about water.
Application Instructions : HOLD BRIGHT is typically used in both blast water and wash down water. It is diluted with water depending on the application, humidity, and level of surface contamination. 100:1 is the most common dilution ratio.
- Dilute In high humidity environments with highly contaminated substrates (e.g. steel plate used in ocean service or exposed to 'dirty" air), 50:1 may be necessary for both cycles.
- Instruction for use Determine the dilution ratio: With low humidity and a relatively clean surface, 100:1 dilution on the blast cycle
- And 100:1 on the wash down should be satisfactory.
- Spray, brush, or dip the metal parts in the diluted solution.
- Ensure full coverage and allow to air dry naturally.
- Do not rinse off after application unless protection is no longer required.
- Surface-dry in 10–30 minutes at room temperature.
- Drying can be accelerated with gentle warm air (below 60°C).
Characteristics
Soluble in water,
• Not classified as hazardous for shipping,
• Biodegradable,
• Phosphate free,
• Non-flammable,
• In dry conditions above +5°C, rusting will be prevented for about 48 hours, often longer,
• Raises pH of blasting water to help compensate for acidic blasting media
• Colourless: Leaves no residue
• Surface salts, including chlorides, undetectable after proper use
Storage Shelf Life is 3 years when stored in cool & dry place. Do not store below 3°C to avoid freezing. Safety Please consult the product label and Safety Data Sheet for safety information. Waste Material Please avoid or minimise waste wherever possible. Please do not discard waste material, including packaging, in the surrounding environment. Follow all relevant legislation for disposa
| Feature | Benefit |
|---|---|
| Prevents Flash Rust | Stops oxidation immediately after acid pickling or rust removal |
| Non-Oily, Dry Film | Suitable for painting, machining, or further treatment |
| Chromate-Free | Environmentally safer, worker-friendly, non-toxic alternative |
| Water-Based and Non-Flammable | Safe to handle, store, and apply |
| Easy Application | Can be sprayed, dipped, or brushed onto metal surfaces |
| Improves Paint Adhesion | Forms a silicate anchor layer that helps bonding of primers and paints |
| Low-Cost, High-Coverage | Economical to use even at low concentrations |
| Short-Term Rust Protection | Ideal for transit, intermediate storage, or process delay protection |
HOLD BRIGHT Prime the surface according to the specification: Priming should be done as soon as possible, before flash rust appears and after the surface is dry. Consult the Primer manufacturer for required surface conditions. Typically, HOLD BRIGHT can prevent flash rust on a freshly prepared surface for 48 hours, or longer with favourable weather conditions, (no rain, ambient temperature above +5°C). These instructions may not cover all circumstances and does not supersede the project specifications.
Need HOLD BRIGHT for your operation?
Our team helps with product selection, dosage, safety data and delivery worldwide.
Request a Quote
